289 High Performance Decal

289 High-Performance air cleaner decal. 1964 - 1967. 7 x 1-1/2. Each.

289™ Side Emblem

Package includes one 289™ side emblem - POWERED BY FORD. This emblem was originally used on the FIA and 289 Cobra. The emblems come with backing pins for proper installation.

Dimensions: 4 3/16" X 1 5/16"

Clutch Boot, Small Block

Clutch lever dust boot for small block engines.

Cobra® Oval Air Cleaner Assembly

Natural Cast Aluminum with raised Cobra letters for a single quad carb. Includes quality air cleaner element and installation hardware. Also used on Shelby Mustangs.

Dimensions: 21 x 10-1/4 x 2-1/2. Each.

Flanges, Exhaust

Made of steel for 2" Tubes. Width 5.00", Thickness 3/8", 4 bolt holes for 3/8 holes with 4-1/4 center to center. Set of two.

Manual 289

Reproduction of the original 289™ chassis manual that were supplied with the cars. Each.

CURRENTLY OUT OF STOCK. Looking into printing a closer replica to the original so it may be February or March of 2016 before we have these again.

Oil Cooler External Adapter

New External type adapter for oil cooler in anodized billet aluminum. Includes Remote Oil Filter Adapter and Take Off Plate with four (4) AN-10 coupler fittings and two ports for Oil Temp and Pressure.

Application: This setup allows the relocation of the oil filter away from the engine block.

Oil Cooler Shroud

Oil cooler shroud designed to channel air flow to the cooler. Fits the Mocal 16 row oil cooler and is made of lightweight Aluminum. Very easy to install. Each.

Oil Cooler, British Style

Original British Style Oil cooler. 235 matrix. Powder coated in silver. Uses AN-10 fittings. Bracket width is 13"x 2" and height is 4 1/4" . Insures your oil cooling capacity and improves your look. Used on SC Cobra 427. Each.

Oval Air Filter Element

High quality replacement oval air filter element that fits oval style air cleaner assembly. Ford, 1965 - 1973.

Dimensions: 20 3/4" X 9 3/4" X 1 3/4"

Overflow Tank, Stainless Steel

Overflow Tank, 2 in Diameter x 15 in Long, Stainless Steel, Each This is the standard coolant overflow tank used on our complete Mk4 Roadster and Type 65 Coupe kits. Made of stainless steel, the capacity is 0.82 qt, and the tank measure 2" in diameter by 15" long. Stainless steel tank captures coolant overflow and recirculates it to the radiator. Machined aluminum cap twists into the filler neck and seals with an O-ring. Inlet/outlet fittings accept 1/4 inch diameter hose. Unit includes mounting brackets and hardware. Measurements are of tank body; add 2 inch for overall length.

Remote Oil Filter Adapter Plate

New External type adapter take off plate for oil cooler in anodized billet aluminum. Includes Take Off Plate with two (2) AN-10 coupler fittings.

Application: This take off plate will be attached at the engine in place of the oil filter. This allows the oil filter to be placed remotely away from the block.

Side Pipe Gaskets

Side Pipe Gaskets. Mounting holes are 4 1/4 center to center. Set of 2.

Spark Plug Wire Separator

Ignition wire Separator. Priced each.

Stellings & Hellings Air Cleaner Assembly

Chrome with a washable foam element., perforated band and hardware. This air cleaner assembly was originally used on both single and dual quad 427's.

Dimensions: 8.5" X 2.5"

Stellings & Hellings K&N Air Cleaner Element

Washable element which provides better air flow rate, minimum restriction, maximum filtration and very long filter life. Increases air flow up to 30% more than regular air filters. Fits Stelling & Hellings air cleaners.

Dimensions: 8.25" X 2"

Will increase the total height of the Stelling 1/2".  

Throttle Cable, Lokar

Lokar Hi-Tech Throttle Cable. Stainless steel braided housing. They are designed with a specially extruded liner for extended life of the cable - not to be confused with ordinary braided brake hose. Cables are equipped with aluminum fittings and aluminum ferrules to eliminate fraying. ''U-Cut-to-Fit'' outer housing isr 36'' with a ''U-Cut-to-Fit'' stainless inner wire. Clevis is designed without cotter pins or set screws. Adapts to factory and aftermarket pedals. Kits complete with installation instructions.

Lokar TC-1000HT36

Throttle Cable, Lokar Polished

Lokar Hi-Tech Throttle Cable. Stainless steel braided housing. They are designed with a specially extruded liner for extended life of the cable - not to be confused with ordinary braided brake hose. Cables are equipped with aluminum fittings and aluminum ferrules to eliminate fraying. ''U-Cut-to-Fit'' outer housing isr 36'' with a ''U-Cut-to-Fit'' stainless inner wire. Clevis is designed without cotter pins or set screws. Adapts to factory and aftermarket pedals. Kits complete with installation instructions. Stainless Steel Braided Housing Throttle Cable Kits Lokar TCP-1000HT36 Polished Finish Fittings

Note: Fittings and ferrules are fully polished. Stainless steel braided cable housing is not polished.

Turkey Pan

Carburetor cold air box, The "Turkey Pan" is made from aluminum to original specs for installation in the 427 Cobra with a single quad carb. Pre-cut for fuel line and linkage. Fits up to a Holley 850.



Dimensions: 14.75" X 10.75" X 5.75 



The Turkey Pan is for function only. It has a rough appearance, just like the original and will not win any beauty contests.

Turkey Pan, Polished

Carburetor cold air box, The "Turkey Pan" is made from aluminum to original specs for installation in the 427 Cobra with a single quad carb. Pre-cut for fuel line and linkage. Fits up to a Holley 850.

Dimensions: 14.75" X 10.75" X 5.75